# Zenithal Highlighting on Miniatures: What It Is and How to Do It

Source: https://minipaintlab.com/blog/zenithal-highlighting-priming-miniatures
Published: 2026-11-17
Publisher: Mini Paint Lab

Zenithal highlighting is a way of pre-shading a miniature by priming it as if light were falling straight down from above. The upper surfaces end up light and the undersides dark, so when you paint on top, the shading and highlights are already in place. It speeds up painting a whole army, and it gives beginners a map of where light should fall. This guide explains the idea, the three-step spray method, what to do when you use a brush or airbrush instead, and how to paint over a zenithal base without losing the effect.

## What zenithal highlighting actually is

The word zenithal refers to the zenith, the point directly overhead. A model primed zenithally is dark in recesses and on its lower edges and light on the tops of shoulders, heads, armor plates and folds, as if the sun were above it. The paint on top of this base picks up the shading automatically if it is thin enough to show it through.

It is a pre-shade rather than a finished look. You still choose colors, glaze edges and add detail. What you save is the first round of shading and highlighting, which is useful when you have many models to paint.

## The three-stage priming method

A common way is to start with a black prime over the whole model. Then spray grey from a roughly 45 degree angle above the model, so the grey reaches the upper faces but leaves the lowest recesses dark. Finally, spray a light coat of white from straight above, keeping the white to the highest points only.

The exact order and angles vary by painter, so treat the above as a starting point and test on a spare model. Hold the can or airbrush at a consistent distance and use short, light passes, since heavy coats cover detail and can leave a grainy surface.

## Doing it with spray cans or an airbrush

Spray cans work, but light coats from a can are harder to control than an airbrush, and the white can come out chalky or blobby if it is applied too thick. A can of grey and a can of white used from a distance are enough for many beginners. Always follow the safety label, spray outdoors or in a ventilated booth and keep sprays away from flame and heat.

An airbrush gives much finer control, letting you build up soft transitions and adjust how strong the effect is. It also lets you use thinned paint instead of aerosol, which many painters prefer indoors with a spray booth and a respirator rated for the paint or solvent in use.

## A brush-only alternative

If you do not own an airbrush, you can imitate zenithal priming with a black base coat and drybrushing in grey and then white on the upper surfaces. The result is rougher, but it does the same job of giving you a light-from-above map to paint over.

Another option is to skip the white and do only black and grey. This makes a softer effect that works well under strong colors and keeps the model from looking too chalky, particularly on small models where a heavy white highlight is hard to hide.

## Painting over a zenithal base

The base shows through thin and translucent paint, so contrast paints, washes, glazes and thinned acrylics all work well on top. Thick opaque coats will cover the pre-shading entirely, so thin your colors and let the light areas shine through, using a second coat only where needed.

Yellows, reds and other light or pale colors benefit the most from a light zenithal base. Dark colors may swallow the effect, so a brighter highlight on top helps. The manufacturer's guidance on a paint's translucency is a good clue before you commit.

## Common mistakes to avoid

The most common problem is overdoing the white, which leaves the model looking like it is covered in frost. Keep the highest layer small and light. Another is spraying too close and filling detail, so keep a steady distance and build up in thin passes.

The last is forgetting that a model will be held and viewed from the side. Zenithal lighting is a visual guide, not a rule, and some models look better with softer shading around the edges. Add your own glazes and highlights to adjust where the effect misses.

## Choosing primer colors and brands

The choice of black, grey and white primers is a matter of preference. Some painters use a single grey primer and add highlights by hand, while others use dedicated zenithal kits. Test any new primer on a spare model, because coverage, drying and finish differ between products.

A matte finish is generally better as a base for later layers, since glossy primers can make later paint slip. Check that your primer is suited to the model material, such as plastic, resin or metal, according to the manufacturer.

## Safety and workspace notes

Aerosol primers produce fumes and fine overspray. Work outdoors or in a ventilated space with a spray booth, wear a mask rated for the product and keep the can away from flame or heat. Follow the safety information printed on the label.

Airbrushing with thinned paint creates less solvent odor, but the mist still needs ventilation and a suitable respirator. Cover the surrounding surfaces and keep children and pets out of the room while you spray.

## When zenithal priming is worth the effort

It pays off most on armies, squads and large models with plenty of surface area, where a quick pre-shade saves hours of manual blending. For a single character you plan to paint with careful glazes, a plain black or grey prime may be simpler, and you can add your own highlights as you go.

Try it first on one test model and compare it with a plainly primed one using the same colors. The difference will show you whether the extra step matches your style, and it takes only a few minutes to find out.

## Related buying guides

- https://minipaintlab.com/best/best-airbrush-primers
- https://minipaintlab.com/best/best-primers-for-miniatures
- https://minipaintlab.com/best/best-airbrushes-for-miniatures
- https://minipaintlab.com/best/best-contrast-style-paints
