Independent buying guides for miniature painting

How to Thin Acrylic Paint for Miniatures: Water, Medium and Ratios

Published How we research

Paint straight from the pot is often too thick for a miniature. It leaves brush marks, fills recesses and turns a sculpted face into a smooth blob. The usual fix is to thin it, but thinning too far makes coverage patchy and the pigment can pool or run. A good mix looks closer to melted ice cream than to water, and it builds up in two or three light coats. This guide covers what to thin with, how to judge the consistency, how a wet palette helps and how to rescue a coat that went wrong.

Products from this article

The highest-scoring picks from the buying guides this article links to. Scores are our editorial assessment, not customer ratings.

As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure

Close-up of colorful acrylic paint tubes on a canvas, ideal for arts and crafts projects
Photo: Ulrich Scharwächter on Pexels

Why thick paint ruins small details

Miniature sculpts rely on shallow recesses and fine edges. Paint that is too thick settles into those recesses and rounds off the edges, so eyes, buckles and fingers lose their definition. It also dries with visible brush strokes, which look much bigger at 28mm scale than on a canvas.

Most hobby paints are made to be used thinner than they come, though the manufacturer's own guidance is the best starting point for a specific line. Dropper bottle paints usually come out already fairly fluid, while older pot paints and some craft paints can be much thicker and may need more work.

What to thin with: water, medium or both

Clean water is the simplest option and works well for small amounts. If you add a lot of water, the paint binder gets diluted and the coat can turn grainy, patchy or weak. Many painters use tap water and others prefer distilled if their local water is very hard, which is a personal choice rather than a rule.

A thinning medium, sometimes sold as a glaze medium or flow improver, keeps the binder in balance and helps the paint flow without losing strength. A common habit is to use medium when you need very thin, smooth layers and plain water for quick small adjustments. Read the label on your own bottle, because products from different makers are not always interchangeable.

How to judge the right consistency

There is no universal ratio, because every brand and even every color behaves differently. Start with a drop of paint on a palette, touch a wet brush to it, and mix. Aim for a coat that is translucent enough that you can still see the surface underneath after the first pass, yet pigmented enough to leave a clear tint.

Test on a spare model, a sprue offcut or the back of a base. If the paint pulls into beads or leaves a tide mark at the edge, it is too thin or the brush is too wet. If it leaves ridges or drags, it needs a little more water or medium. Adjust by one small drop at a time.

Use a wet palette to hold the mix

Thin paint dries quickly on a dry surface, and the tip of your brush can dry out and leave a crusty edge. A wet palette keeps a mixed puddle usable for much longer, and the thinned paint stays at the same consistency while you work. It also saves you from remixing the same shade several times.

If you do not have one, you can use a ceramic tile or a plastic lid and mix smaller amounts more often. Either way, keep a separate water pot for rinsing so you do not accidentally dilute your paint with dirty water.

Build color in thin layers

Two or three thin coats usually give a smoother, more even result than one thick coat. Let each layer dry before the next, which often takes a few minutes for thin acrylic, though conditions in your room change this. Brushing over a wet layer can lift the paint underneath and leave a patch.

Thin layers also make blending easier, because each pass adds only a little tone. For glazes and smooth shading, the mix can be thinner still, closer to a tinted water, but only on a base coat that has fully dried.

Fixing chalky, streaky or runny results

Chalky or grainy dry paint often means too much water or very thin paint dried too fast. Add a little medium to the next mix, use a slightly bigger brush load and keep the paint moving. Streaks usually come from a half-dry brush or a mix that is too thick, so refresh the paint on your palette and reload.

If paint runs into recesses and pools, the mix is too thin or the brush is overloaded. Wick away the extra with a clean, damp brush or the edge of a paper towel, and wait for the spot to dry before touching it again. Safe hobby habits apply: work in a well-ventilated room and wash your brushes in the sink rather than drinking from or cleaning near food cups.

Thinning for different jobs

Base coats can usually be a little thicker, because the aim is even coverage over primer. Glazes, shading and smooth transitions need much thinner paint, sometimes with a medium added so the color stays translucent. Washes are thinner still and are normally bought ready to use.

Metallic paints and inks behave differently from ordinary colors. Metallics carry heavier particles that can separate, so stir them well and be careful with water, while inks are often sold already thin. Check the label for each product and test on a spare model before using it on something you care about.

Keeping a consistent routine

Stir or shake every bottle before use, since pigment settles over time and the first drops can be watery while the last are thick. Put out a small amount on the palette rather than painting straight from the pot, and close the lid so the rest does not dry out.

Many painters keep notes about what works, such as how many drops of water or medium suit a given range. That is more reliable than copying someone else's ratio, because your brushes, your water and your room all change the result.

When thinning is not the answer

If a paint is thick because it has dried out in the pot, adding a lot of water may not bring it back, and old paint can have clumps that never mix smoothly. A few drops of medium and a good stir can sometimes help, but badly dried paint is better replaced.

If coverage is poor even at the right thickness, the problem may be the color itself. Some reds, yellows and whites are naturally translucent and need an underlayer in a similar tone. Painting over a light or grey base coat helps these colors reach full strength without being thickened.

Popular right now

  1. The Best Miniature Carrying Cases for TransportBuying guide
  2. Best Texture Paints for Basing MiniaturesBuying guide
  3. Best Drybrushes for Miniatures and TerrainBuying guide
  4. The Best Magnifiers for Miniature PaintingBuying guide
  5. Best Miniature Paint Sets for Tabletop PaintersBuying guide
  6. Best Speed Paints for Fast Miniature PaintingBuying guide

Based on the last 28 days of search and visitor data.